Do p bass pickups hum?

11
Walton Connelly asked a question: Do p bass pickups hum?
Asked By: Walton Connelly
Date created: Mon, Jun 14, 2021 9:21 AM
Date updated: Tue, Aug 2, 2022 6:40 PM

Content

Top best answers to the question «Do p bass pickups hum»

However, the original "vintage" Fender Precision Bass pickup is a single pickup with a single coil, and it is not noise-cancelling -- it is subject to 60-cycle hum electrical interference. The original single-coil design is less popular, but it is favored by some traditionalists, notably Sting.

FAQ

Those who are looking for an answer to the question «Do p bass pickups hum?» often ask the following questions:

🏁 Can a lindy fralin pickup cancel out hum?

  • “These Fralin pickups are working like a charm. They're cancelling out hum in the bridge and neck settings, and at the same time, bringing a world of definition to my Fender Jazzmaster. Perfect!”

🏁 Do mid bass crossover block out lows?

Attached is the schematic for two one-pole passive filters to perform the crossover function at 120Hz. Note that most crossovers for this function are two-pole for faster rolloff but that involves very large inductors to make passive filters at this low frequency. That's why active filters are usually used at audio frequencies.

🏁 Does a crossover improve bass?

Fortunately, Crossover processors let you specify which Bass frequency range you want steered to the Subwoofer. Called the Crossover Frequency, this setting sets the dividing line: Higher frequencies go to the speaker and lower frequencies go the Subwoofer.

🏁 Does crossover affect bass?

  • Shown: One of the most common crossovers used directly on speakers and the crossover frequency as a real-world example. As tweeters can’t produce bass sounds, they distort and can even be damaged by heavy bass. Using a crossover, therefore, makes it possible to block (filter out) unwanted sounds below the crossover frequency.

🏁 How do you set up a crossover bass?

Set the crossover point 10 Hz higher than the low end of your speaker's tolerance range. If you don't know the frequency range of your speaker, use a subwoofer matching tool. Listen for smooth transitioning between the subwoofer and the speakers. The blending should sound clean and seamless.

🏁 How to connect bass crossover?

How to Use and Install Bass Blockers and Crossovers. Watch later. Share. Copy link. Info. Shopping. Tap to unmute. If playback doesn't begin shortly, try restarting your device. Up Next.

🏁 What dose bass crossover for car mean?

Put simply, a crossover is an electronic device which is wired between the amplifier and the car speaker to ensure bass frequencies are sent to bass speakers and treble frequencies are sent to treble speakers. Inappropriate frequencies are removed to ensure the speaker does not play distorted sounds. For example, low (bass) frequencies will be ...

🏁 What is a bass blocker crossover?

  • Bass blockers as they’re called are a type of inline 1st order (single stage) crossover used with tweeters or smaller speakers to block bass. If you don’t know the crossover frequency you can calculate it yourself using just a bit of math. First-order crossovers use a single inline capacitor or inductor.

🏁 What is bass crossover?

Crossover is the frequency where speakers begin to roll off, and the subwoofer starts outputting bass notes and LFEs. Most of today's systems have an EQ feature that will set up the proper crossover automatically based on the specifications of your speakers.

10 other answers

Hum is the 60/120 Hz stuff you get from single coils. It doesn't go away when you touch the strings. It's caused by magnetic field interference. Humbuckers get rid of hum. Twisting leads helps with hum also. Buzz is that high pitched electrical field noise. Humbuckers, such as the P bass pickup, can't get rid of buzz. Shielding fixes that.

I've never played a bass or guitar that didn't have a little bit of hum when not grounded (ie not touching the strings/bridge/tuners) shielding will reduce it a bit. take the pickguard off and have a look at if the control cavity is shielded and how well.

Humbucking pickups usually have two coils per pickup to deal with 60 cycle hum. So, when you have both pickups on full the two pickups act as one humbucking pickup essentially. Depending on the wiring wherever you play gigs the hum that can be either more or less if you solo one of the pickups on your j-bass.

So that’s humbucking in a nutshell. If you still don’t understand it (I have a hard time with this too), don’t fret. All you really need to know about the P pickup’s humbucking mechanics is that it is designed to get rid of feedback and background noise and does so in a really clever way. P Bass Pickup Tone

Shielding does not address 60hz hum. Additionally, if your bass makes a popping sound when you touch metal/strings/bridge you are hearing static electricity discharging. Shielding will resolve the issue. As far as I know RF interference issues only arise with passive pickup basses. Just because your bass has a pre-amp does not mean it has active pickups. Some basses, such as the Musicman Stingray, are passive with an active pre-amp.

Now, as you can see on the image above, there IS a difference between P-bass pickups and humbuckers (both double coil pickups)…. Because, although they both are humbucking pickups, humbuckers have 2 coils under each string, allowing them to ‘pick up’ a wider area under the string, and creating some phase cancelation….

Hi all, I have a P-Bass which I have just gutted and stupidly (I know) replaced the electrics in, without taking careful note of how it was wired before. Before all this began, there was a quiet hum when not touching the strings, now the pickup and electrics are in there, there's a slightly louder hum again which goes away if you touch the strings.

Below is a list of the best five, with detailed pros and cons. All you have to do is pick and click. Top 5 Best P-Bass Pickups – Comparison Table. These are, in our humble opinion, the best P-Bass pickups on the market.

As before, the signal from the strings is inverted. But the hum is not inverted! That’s because the hum isn’t induced by the magnetic field of the pickup – it comes from other magnetic fields in the surrounding environment. If we were to sum these two signals, we’d cancel our string sound out completely, but double the hum!

Secondly, noiseless pickup manufacturers haven’t really been able to refine their process to a degree where the hum is completely eliminated. You will only get a reduced hum (which will be particularly noticeable when you use distortion) and if our main target is to eliminate hum, well noiseless pickups will not do the job.

Your Answer

We've handpicked 6 related questions for you, similar to «Do p bass pickups hum?» so you can surely find the answer!

What is bass redirection crossover frequency?

crossover frequency. Clicking on “Bass Redirection” enables the Crossover Frequency slider to balance what goes to the subwoofer and satellites. On a system that does not use full-range speakers, this is a crucial setting for ensuring that your speaker system correctly plays low frequencies. If set improperly, you may hear distortion or gaps

What should be the crossover frequency for bass?
  • And with Bass audio, that means understanding why you need to include a Subwoofer in your speaker configuration, and learning how to select a Crossover Frequency to drive it. There's no set definition of what constitutes Bass frequencies, but for purpose of discussion lets focus on frequencies below 150 Hz.
What should i set my bass crossover to?

What is the recommended crossover frequency for a subwoofer? For THX Certified and non THX Certified home theater systems, 80 Hz is the recommended setting. However, you can set the crossover (LPF) between 80 Hz - 120 Hz based on which setting sounds best for your system.

What's the best crossover frequency for bass steering?
  • A typical Crossover Frequency would be 80 Hz. And you'll recall from that table linked above, this is a "safe" frequency for Bass steering, since the wavelengths of audio 80 Hz and lower are going to be long enough to trigger that "pressurizing" effect -- i.e.,to be "non-localizable".
Which is the best pickup for a hum-free sound?
  • Since the invention of the electric guitar, the most common type of pickup is a single coil. Its clear and bright tone had become a symbol of blues and early rock music. But single-coils have one significant disadvantage. They produce a hum. There are several ways to get a hum-free sound. The first of them is the noise gate.
Which is the correct pickup height for bass?
  • The correct pickup height orientation is lower on the bass side and closer on the treble side. Your Bass strings have more mass and will disturb the magnetic field more than treble strings. Reversing your pickup height orientation will provide you with “warbling” bass strings and thin treble strings – not good. Lindy’s Take On it: