Do you have to use crossover with component speakers?

12
Clare Grimes asked a question: Do you have to use crossover with component speakers?
Asked By: Clare Grimes
Date created: Wed, Jan 20, 2021 3:53 PM
Date updated: Tue, Aug 30, 2022 9:04 PM

Content

Video answer: Is passive crossover pointless if your audio system has a dsp?

Is passive crossover pointless if your audio system has a dsp?

Top best answers to the question «Do you have to use crossover with component speakers»

If your car audio system uses coaxial speakers, you probably don't need an additional crossover… Even if you add an amplifier into the mix, the built-in speaker crossovers should be more than sufficient. However, you may need a crossover if you add an amplifier and a subwoofer to that type of system.

Every speaker system needs a crossover of some type. Component speaker sets come with separate outboard crossovers, many with tweeter level selectors. Every full-range, coaxial speaker — with its tweeter mounted in front of the woofer cone — already has a tiny crossover network built into it somewhere.

FAQ

Those who are looking for an answer to the question «Do you have to use crossover with component speakers?» often ask the following questions:

🏁 Do you have to wire both speakers at the crossover point?

  • Even with crossovers, both speakers will produce sound for several octaves beyond the crossover point. If this problem occurs, there will be a noticeable dip in the frequency response at the crossover point. To solve this problem, wire one, but not both, of the speakers backwards (+ to -).

🏁 How do you connect speakers to a crossover?

Passive Crossovers

They each go between your amplifier and a speaker and do not require a power connection, a turn-on lead, or grounding. You connect the speaker wire coming from your amp to the crossover's input. Then the tweeter gets wired to the tweeter output, and the woofer to the woofer output. That's it.

🏁 How do you hook up crossover speakers to a car?

  1. Determine your speakers' frequency range…
  2. Set the crossover point around 10 Hz below the lowest frequency your speakers can produce without issue…
  3. Once again, play some music…
  4. Now set the gain of your subwoofer amp to its lowest possible value (a full counterclockwise position).

🏁 How do you hook up speakers to a crossover?

  • Attach your speakers to the crossover using speaker wire, similarly to the previous step. Your crossover should have separate outputs for your woofers (bass speakers) and tweeters (treble speakers). Make sure to wire the correct speaker into the correct output.

🏁 How do you remove crossover from sansui speakers?

  • I should’ve hosted it here instead. Unlike newer speakers (including a pair of Sansui SP7500X that are still waiting to be refurbished), these are very easy to remove. Six screws to remove the crossover panel from the back, disconnect the driver leads from the spade terminals, and pull out of the back.

🏁 How does a crossover for speakers work?

A crossover splits the music into two or three different signals (sometimes more, depending on how many different drivers a speaker system has), and sends the low frequency, or bass, signal to the woofer, the high frequency, or treble, signal to the tweeter and so on.

🏁 How to connect crossover to speakers?

You should properly install car speakers in the trunk before connecting a crossover. For that, the first thing while setting up the crossover is to end up every band of frequency which the tweeters can be, subwoofers and midrange speakers. For instance, just play them at the same volume.

🏁 How to match crossover to speakers?

Go to your receiver’s setup menu with the remote to find the part of the menu that highlights the size of your speaker and crossover point. The process of finding this menu will vary from one product to the other, so you may have to use your product manual.

🏁 How to set up crossover speakers?

Here’s how to do it: Find the low-end of the subwoofer’s frequency range either from your user manual or from the manufacturer’s website. Set the crossover point 10 Hz higher than this range for the best result (or go with the recommended 80 Hz). Listen for a smooth transition between your subwoofer ...

Video answer: Improve sound protect speakers - how to set crossovers - caraudiofabrication

Improve sound protect speakers - how to set crossovers - caraudiofabrication

10 other answers

Using a crossover allows control over which frequencies are sent to which speakers, so that all speakers in the system work together to achieve the best possible sound quality. Sending a full-range signal to all speakers within the system, regardless of each speaker’s design, can be problematic.

It’s generally easier to put a crossover near the component speakers when upgrading (or adding your own) 2-way speaker systems. However, there’s no reason you have to most of the time. When it’s convenient, you might find it helpful to keep the crossover closer to the car stereo or amp, saving the need to do more work or run new speaker wire to go to it.

Mike, You should use the crossovers that came with your components. They divide the signal between the tweeters and woofers. You would then use the high-pass crossover filter on the amplifier to keep away extreme low notes that could distort the sound of the speakers.

Why do I need high quality crossover components? Both inductors and capacitors will have some resistance. Usually, it is small but sometimes it can be greater than the resistance of the speaker itself. Since the entire crossover network is based on the resistance of the speakers, this can be very bad.

The crossover is a filter network that makes sure the tweeter and woofer (and midrange) play only what they are supposed to play. But you can imagine that any time you have such a filter, crossing over to different speaker drivers, you’re going to get “non-perfect” reproduction. They are a necessary compromise.

The crossovers for the front component speakers and subwoofer (s) are identical to System One. The only difference is we have added rear coaxial speakers. Most coaxial speakers do not come with supplied passive crossovers. Instead they use a basic filter to block low frequencies from being sent to the tweeter.

Jul 9, 2007. #12. You can run without the crossover, but you need to know how to tune it on your headunit or your amp for it to be able to work right, or without damaging the speakers as you stated. More then likely use crossovers. References: integra88, goonandbuck, ls2poweredgoat, AZ-ss, mattmcss, DeuceLee, Starky.

Edit: component speakers that have the external crossovers need them installed. Run the line that hooks to the factory speaker(not tweeter, but shouldn’t matter) and run wires to the woofer and tweeter respectively. P.S. Alpine components have crossovers for the woofer integrated on the speaker basket. Tweeters have the inline crossover

Component speakers also come with external crossovers, so the wires running from the receiver must first be routed to the crossover, and then to the individual woofers and tweeters. If connecting an amplifier as well, the amp should be wired between the receiver and the crossover.

The component speaker refers to the speakers that consist of separate crossovers, sub-woofers, tweeters, super tweeters, and woofers. When you use these parts together, you will have a speaker system that covers a whole audio spectrum. Woofer. The woofer can create sounds, having 10-1000 Hz frequency range.

Your Answer

We've handpicked 6 related questions for you, similar to «Do you have to use crossover with component speakers?» so you can surely find the answer!

How to wire component with inline crossover?

Hi Erik. Most likely you can’t use the original wiring to the factory tweeters (if there are any installed). You’ll need to wire it like this: 1. CD player -> crossover + & – inputs. 2. Crossover woofer out -> door speakers (can use the factory wiring if you like). 3. Crossover tweeter out -> run wire to the new tweeters in the dash. Reply

What does crossover mean in speakers?

The speaker crossover is a component hidden within just about every loudspeaker… As its name suggests, a crossover is where the unfiltered audio signal is divided according to a predefined upper or lower threshold. The speaker crossover supplies each driver with the signal range it was designed to best reproduce.

What is a crossover in speakers?

The following guide might help, showing recommended crossover frequencies for different speaker/subwoofer combinations: Small bookshelf or satellite speakers (4-5 inch woofer): 150-200 Hz Medium sized bookshelf speakers (6-8 inch woofer): 75-100 Hz Large floor-standing speakers (10-12 inch woofer): ...

What is crossover in audio speakers?
  • A passive 2-way crossover designed to operate at loudspeaker voltages. Audio crossovers are a type of electronic filter circuitry used in a range of audio applications, to split up an audio signal into two or more frequency ranges, so that the signals can be sent to drivers that are designed for different frequency ranges.
Where should i put speakers crossover?

Active Crossovers

You'll mount your crossover securely, preferably near the amplifiers; give it power, remote turn-on, and ground wiring, like the amps have; and get signal from the receiver and send it to the amps.

Video answer: How to connect a crossover component in series or parallel

How to connect a crossover component in series or parallel Why does my subwoofer not crossover with my speakers?
  • If there’s a noticeable discontinuity, slowly increase it to get the transition you want. There’s a chance that during your tests, you’ll hear bass bumps while your speakers and sub are overlapping. It’s not an issue with your crossover, but rather with the output volume.

Video answer: What is my crossover doing to my speakers?

What is my crossover doing to my speakers?