How do you change a throttle cable on a go kart?

10
Jasper Swift asked a question: How do you change a throttle cable on a go kart?
Asked By: Jasper Swift
Date created: Mon, Apr 5, 2021 12:42 PM
Date updated: Thu, Jun 30, 2022 11:16 AM

Content

Top best answers to the question «How do you change a throttle cable on a go kart»

Throttle cables have adjustment at both ends, make all adjustments at engine side. Loosen the jam nuts and move the housing closer to the throttle arm to decrease the amount of throttle pull, move the cable away from the throttle arm to increase the amount of pull. Tighten jam nuts when completed.

FAQ

Those who are looking for an answer to the question «How do you change a throttle cable on a go kart?» often ask the following questions:

🏁 Do you need to replace the throttle on a razor go kart?

  • Speed control module and throttle kit for all versions of the Razor® Ground Force Drifter electric go kart. When installed on a version 1-2 Ground Force Drifter the control module and throttle both need to be replaced at the same time. Speed control module for version 3 and up of the Razor® Ground Force Drifter electric go-kart.

🏁 How do i fix the throttle on my go kart?

Ensure your throttle pedal is placed against the back-pedal. Drag your throttle cables towards the back of your go-kart until you notice resistance, then stop pulling. You need to fix cable housing in this position and tighten your frame with the jam nuts at the front.

🏁 How to fix a throttle cable on a go kart?

Fully loosen the jam nuts (1) and (2) and mount the throttle cable housing to the frame. Make sure the throttle pedal is against the rear pedal stop (3). Pull the throttle cable housing toward the rear of the kart until you feel resistance. Warning: DO NOT pull the throttle cable housing any further.

🏁 How to hook up remote throttle cable on go kart?

Here is a quick video of how easy it is to set up a throttle cable on a go kart. I have used Harbor Freights Predator engines a lot and for the most part the...

🏁 How to install throttle cable on go kart?

Fully loosen the jam nuts (1) and (2) and mount the throttle cable housing to the frame. Make sure the throttle pedal is against the rear pedal stop (3). Pull the throttle cable housing toward the rear of the kart until you feel resistance. Warning: DO NOT pull the throttle cable housing any further.

🏁 How to put a throttle cable on a go kart?

Here is a quick video of how easy it is to set up a throttle cable on a go kart. I have used Harbor Freights Predator engines a lot and for the most part the...

🏁 How to reduce the throttle on a go kart?

  • Reduce the throttle setting by first loosening the clamp bolt or nut and rotating the throttle plate clockwise until it stops. Attach the nut driver on the governor shaft and turn it clockwise as you allow the throttle plate to rotate away from the full-throttle position. Tighten the clamp bolt.

🏁 What do i need for a go kart throttle?

  • Go kart throttle setup instructions include the go kart throttle pedal, return spring, cable, and engine linkages. When installing a go kart throttle cable following the free go kart plans that I have on my site, I used the following throttle cable parts from the kit.

🏁 What kind of throttle cables do you need for a go kart?

  • Manco Throttle Cables, American Sportworks Throttle Cables, Shift Cables and Choke Cables. American Landmaster UTV Cables: Throttle Cables, Choke Cables, Parking Brake Cables, Shifter Cables and Differential Cables. Yerf Dog Throttle Cables. Universal Cables. Throttle Linkage Kits for Predator Engines. Innerwire length shown above.

9 other answers

After you have the throttle pedal, stops, and cable tab installed, it is time to install the go kart throttle cable. Referencing the picture above, you simply unscrew one of the bolts on the cable housing, and slide the end through the tab’s 5/16″ hole. You will need to remove the inside cable from the housing to do this.

Here is a quick video of how easy it is to set up a throttle cable on a go kart. I have used Harbor Freights Predator engines a lot and for the most part the...

throttle cable with a Pedal on a Gokart or a Twist Grip on a Minibike. When installing a new throttle cable, you both the conduit (outside housing) and the cable to fit your application. Since you can usually only cut once, maybe twice, BE SURE BEFORE YOU trimmed later. Try to cut the excess cable after it is installed if you can.

Knowing how to adjust your throttle c... Throttle freeplay is a terribly overlooked adjustment that can change both the reaction and comfort of your motorcycle.

In order to to do this you must first attach one end of the the throttle cable to the throttle on the engine. Once that’s attached, you must run the throttle cable down the chassis towards the throttle pedal. Afterwards cut the throttle cable leaving atleast 6-8 inches of slack. Then attach the loose end to the throttle peddle.

Installing a throttle cable is very easy if you understand the mechanics of how it works. This video will show you how to install a throttle cable on any sma...

Cables, rods, and fittings for all types of go-kart brake and throttle setups. Also all the hardware needed from clevis, wire stops, springs, and more!

Video showing the common methods of installing throttle and choke cables on both the auto choke and manual choke engines, how to adjust them and how to chang...

When it’s time for a replacement. While you can adjust a throttle cable, you can only do so up to a certain point. Typically, that’s because there are no more threads for the nuts to move on. Once you get to that point, you need a new cable. And, naturally, if it breaks completely, Autoblog explains.

Your Answer

We've handpicked 6 related questions for you, similar to «How do you change a throttle cable on a go kart?» so you can surely find the answer!

What's the throttle linkage kit for a go kart?
  • This can be one of the biggest challenges in ordering correct parts. If you ordered your Vehicle from us, we can look-up your records. GO KART & MINI BIKE Throttle Linkage Hardware kit used to hookup your throttle cable to your engine. Includes Springs, Wire Stops and Cable Crimp conectors. Honda, Titan and Predator Engines.
When to use throttle on a go kart?
  • Use the throttle to help turn the car In the wet, there will be much less grip than usual, and a kart will not want to turn due to its fixed rear axle pushing it straight on. Applying a small amount of throttle in the middle of slow hairpin turns will help the kart rotate towards the exit and point you in the direction you want to go.
Where can i get go kart throttle cable?
  • Go Kart Cable Clamps and Go Kart Cables at Kart Parts Depot! Find your go kart throttle cable, accelerator cable, brake cable, clutch cable, and control cables here plus cable clamps and outer cable housings. Whether you need ball end cables or barrel end cables 72 inch cables or 2 meter cables we have them.
Where do you put the throttle tab on a go kart?
  • This will limit the travel of the throttle pedal so your cable will not stretch out if you push on the gas too much, nor will it allow the pedal to hit the tie rods as you step on the gas. Cable Tab: Weld the throttle cable tab on about a 45 degree angle on the center beam of the kart.
Where is the throttle linkage on a go kart?
  • Make sure the engine throttle linkage is in the idle position and the throttle pedal is against the rear stop. Block the rear end of the kart up off the ground and start the engine. If the engine is not at idle speed, stop the engine and repeat the above procedures.
Where to put throttle cable in mikuni go karts?
  • We put the clip in the middle for baseline testing and go from there. To setup your throttle cable, insert the throttle cable into the top of the carburetor cap. The rubber boot on the cap will hold the cable in place. Your cable will need a lead ball or barrel on the end of the cable wire.