How to choose a crossover for tweeters and woofers?

9
Roy Hegmann asked a question: How to choose a crossover for tweeters and woofers?
Asked By: Roy Hegmann
Date created: Sat, Jul 3, 2021 8:40 AM
Date updated: Sat, Jan 15, 2022 3:15 AM

Content

FAQ

Those who are looking for an answer to the question «How to choose a crossover for tweeters and woofers?» often ask the following questions:

🏁 Do tweeters need a crossover?

Do tweeters need crossovers? A: Short answer: an active crossover needs power — a passive crossover does not. Passive crossovers go between the amplifier and the drivers (tweeters, speakers, and subs)… An active, or electronic crossover goes between the receiver and the amp. Can you amplify tweeters? A tweeter produces high-pitched noises and are usually about 2 inches in diameter. Both a tweeter and a subwoofer can be hooked up to the same amp. However, the sound quality will be ...

🏁 How to use a crossover with two woofers?

Since the driver are in parallel, that is a four ohm load. Off the shelf crossovers are never satisfactory. All crossover need to be custom. That design really needs to be 2.5 way. Driving two woofers in parallel up to 2K is not a good idea. It should be possible to design a good 2.5 way speaker for those drivers.

🏁 Can you run tweeters without crossover?

For starters, they do not need to be connected with any other speaker for the music to reach your ears. Moreover, they help improve sound quality by providing clear highs and smooth mid-range frequencies. Tweeters without crossover are also compatible with any vehicle out there.

9 other answers

To design your own speakers, you need at least a tool to measure impedance and frequency response - for example a Dayton DATS, Mic Preamp, and Mic at the very least. Along with the cost of tweeters and crossovers, it would probably end up costing quite a good bit for a pair of 10 dollar woofers.

A typical 2-way crossover point might be 3kHz (anything above goes to the tweeter, anything below goes to the woofer). Typical 3-way crossover points might be 160Hz to 200Hz between the woofer and mid-range, and then the 3kHz point between the mid-range and tweeter. Passive Radiators and Ports A passive radiator looks like a speaker.

Think of a crossover network as an audio traffic cop, directing highs to your tweeters, midrange to your woofers, and low bass to your sub. Without a crossover, a messy, sonic "traffic jam" results. Your midrange and sub duplicate too many of the same frequencies and your sub wastes time trying to put out high notes it wasn't meant to handle.

Making changes and measuring with an active crossover or digital crossover is easy and painless. Wavelength also works as you move away from the baffle so if the crossover frequency is set at 3000Hz and the drivers are placed further apart you will get lobeing if the midrange and tweeter drivers are more than 4.5 inches apart.

That’s where woofers and tweeters come in. A woofer is a speaker designed for low-frequency sounds and a tweeter is a speaker designed for high-frequency sounds. Woofers. At a glance, the main difference between woofers and tweeters is that the woofers are a lot larger than the tweeters. A good woofer might be 12 inches in diameter or more.

For tweeters and 2-way speakers: the recommended crossover frequency is 3.5 kHz (high pass, or high/low pass). Anything below this range for these speakers will lead to suboptimal performances. For midrange speakers and woofers: the recommended crossover frequency is 1-3.5 kHz (low pass). Most woofers and midrange speakers don’t deliver quality sounds above this range.

Choosing the crossover frequency is a matter of matching the driver to the audio range you expect it to be used in. It is not a linear process, so calculations are based on experiments and past experiences. A frequency range of 80 Hz to 120 Hz is ideal for a woofer. While a tweeter should be chosen in a range of 2,000 Hz to 20,000 Hz.

When you select a crossover frequency, slope and alignment in your DSP, you are selecting an electrical response that will be applied to the acoustic response of the speakers. The acoustic response is what matters. In order for the crossover to work properly, the sound of the speakers has to arrive at the listener or the mic at the same time.

As we said before, a crossover will send high frequencies to the tweeter, a range of frequencies which that tweeter can most effectively and safely reproduce, and it will do the same with the woofer, sending only those deeper frequencies the woofer can handle with good sound and no damage.

Your Answer

We've handpicked 24 related questions for you, similar to «How to choose a crossover for tweeters and woofers?» so you can surely find the answer!

How to wire tweeters with built in crossover?

To strip tweeter speaker wire: Insert the wire in the stripper and close it carefully on the insulation. Use enough force to hold the wire in place and slightly pinch the insulation, but not enough to put force on the wire inside. Hold the tool & pressure in place firmly so it cannot move.

What does crossover mean in terms of tweeters?
  • A crossover is an electronic circuit that, in the case of a tweeter, filters out the low-frequency elements of the audio signal. That way, the tweeter is left to do what it does best, which is reproduce high-frequency sounds. What Does Sensitivity Mean?
Can you use tweeters on a low pass crossover?
  • You cannot use tweeters on a monoblock (bass-only) amp or a subwoofer output channel using a low-pass crossover. You can use tweeters with unused amplifier outputs (channels) that are full-range. Why can’t you use tweeters on a monoblock sub amp or bass output?
Do separate tweeters need a crossover in a car?

Can you wire a speaker crossover to a car stereo?

  • The good news is that yes, you can wire speaker crossovers close to your amp or car stereo if it’s less work. While it’s usually easier to do it where the speakers are when upgrading factory 2-way component speaker systems (since they’re often close to each other in the doors, for example), it’s not important.
How to install tweeters in a car without crossover?

How to Install Tweeters Without Crossovers? Step 1 – Safety precautions Before you begin the installation process, switch off the ignition of your car. Next, open the hood and unhinge the nut attached to the negative charge of the battery.

Is it necessary to connect a crossover to tweeters?

Connect them to unused amp channels with a full-range output option: Follow the positive and negative wiring connections on the amp, being sure to match the same speaker polarity at the tweeter (either on the tweeter or marked on the external crossover for those that use an inline one).

How to hook up my tweeters with built in crossover?

Connect them to unused amp channels with a full-range output option: Follow the positive and negative wiring connections on the amp, being sure to match the same speaker polarity at the tweeter (either on the tweeter or marked on the external crossover for those that use an inline one).

Where is the crossover for tweeters in a pillar silverado?

Installing 03-06 Tahoe A pillar tweeters on 02 Silverado any questions comment down below #Silverado #ondgas #trokiando #takuache

How to choose crossover frequency?

Six Methods to Choose Crossover Frequencies There's more than one viable way to approach many tasks. Explore six methods of deciding crossover settings for your... Each method varies in complexity and the limit is on how much you want to practice and study. Already have the book Crossover Curving: ...

How to choose crossover hertz?

If they are rated down to 30 Hz, the Crossover Frequency should be no lower than 60 Hz. If they are rated down to 50 Hz, the Crossover Frequency should be no lower than 100 Hz, If you think about that, some problems should immediately jump to mind!

How to choose a crossover suv?

The majority of modern SUVs, sometimes called crossovers or crossover utility vehicles (CUVs), utilize a structure that resembles a typical car more closely than it does a body-on-frame truck, as...

How to choose subwoofer crossover frequency?

Check out the entire SVS Subwoofer line-up to choose the subwoofer that is best for your TV/movie viewing. If you know your speaker’s frequency range, set the crossover point roughly 10 Hz above the lowest frequency your speakers can handle cleanly The most common crossover frequency recommended (and the THX standard) is 80 Hz.

Do tweeters need crossovers?

Why Do You Need A Crossover? Every audio system, including the one in your car, needs a crossover to direct sound to the correct driver. Tweeters, woofers and subs should get high, mid and low frequencies respectively. Every full-range speaker has a crossover network inside.

How do you choose a crossover slope?
  1. Choose a CO slope of 12 dB.
  2. Choose a CO slope of 24 dB.
  3. Try different crossover points between 40hz and 80 or 90 hz, depending on your speakers/sub (keep the CO and slope the same)
  4. Try different crossover slopes for the mains and subs.
How to choose the best passive crossover?

Passive crossovers For home use, a 3-way passive speaker system is cost effective and adequate for most people. It is possible, but not practical to make a 4-way passive crossover system. To make a 3-way passive system into a 4-way, the bass (sub-bass) should be active (driven by a separate amplifier).

How do i choose a crossover for speakers?
  1. If you know your speaker's frequency range, set the crossover point roughly 10 Hz above the lowest frequency your speakers can handle cleanly.
  2. The most common crossover frequency recommended (and the THX standard) is 80 Hz.
How to choose a crossover for your box speakers?

How To Pick A Crossover Type | Step 2 | DIY Speaker Building. Watch later. Share. Copy link. Info. Shopping. Tap to unmute. If playback doesn't begin shortly, try restarting your device. You're ...

Do i need crossovers for tweeters?

Every audio system, including the one in your car, needs a crossover to direct sound to the correct driver. Tweeters, woofers and subs should get high, mid and low frequencies respectively… If these frequencies aren't directed properly, then speakers will try to play sounds they aren't meant to play.

How to connect tweeters crossovers app?

Tweeters – even budget ones – can make a huge difference in your system. However, you may need to know a bit more before getting started. I’d love to help! In this article, I’ll show you how to wire tweeters with built-in crossovers to an amp.

What do crossovers do for tweeters?

There are two crossover types–active and passive. Passive crossovers don’t require power and offer limited control over the volume of each channel. They limit control by allowing the tweeter volume to be adjusted relative to the woofer volume.

How do you install tweeters and crossovers?

How to Wire Tweeters In a Car: Install or add a crossover and connect it to an amplifier or the external head unit source. Connect the other site of the crossover with the main power. After that, plug in the high-frequency wire from the crossover to the tweeter and low-frequency wire from crossover ...

Do tweeters have to be hooked to crossovers?

the tweeters popping is from them getting lower frequencies. so ya, you need a crossover. sometimes they will put a cap on the speaker as a crossover, not that i've ever trusted that to be a good crossover.

What is crossover claims crossover?
  • Introduction – Crossover Claims Crossover is the transfer of processed claim data from Medicare operations to Medicaid (or state) agencies and private insurance companies that sell supplemental insurance benefits to Medicare beneficiaries.
What makes a crossover a crossover?
  • What makes a crossover a crossover. Crossovers thrive because they marry car and truck. Essentially tall station wagons with passenger car handling and efficiency, crossovers offer the comfort and utility that once boosted SUVs, but with a softer ride. Sharing architecture makes better crossovers possible, now and in the future.